What a new installation includes.
A proper install is more than swapping a tank. It includes shutoff valves on the cold supply, flexible connectors or hard piping, a temperature and pressure relief valve with a full-size drain line, a drain pan where a leak would do damage and a vent or electrical connection to match the unit.
On gas units we also install a sediment trap and a gas shutoff, and we check the flue draw after firing. A thermal expansion tank is added where the plumbing is a closed system, for example when a pressure-reducing valve or check valve sits on the supply.
We take photos of the finished job so you have a record.
Fuel and unit options.
Choose by what your house already has and how you use hot water.
| Option. | Install needs. | Good fit. |
|---|---|---|
| Gas tank. | Gas line, flue, combustion air. | Homes with gas service and a chimney or power vent. |
| Electric tank. | Dedicated 240 volt circuit. | Homes without gas, or where venting is hard. |
| Hybrid heat pump. | Space, drain, 240 volt circuit. | Basements with room and moderate temperatures. |
| Tankless. | Venting, gas or heavy power. | Households that want continuous hot water. |
Planning a new water heater? Call and we will check the space, venting and supply first.
Call (855) 575-2890New construction and additions.
In a new build or an addition, the water heater should be planned with the plumbing layout. Placing it near the bathrooms and kitchen shortens hot-water wait times and saves energy.
We coordinate with the builder on rough-in locations, venting paths and electrical, so the unit fits without changes later. See also our plumbing installation page for fixtures and rough-in.
From first call to hot water.
Survey the space.
We look at the location, access, venting, gas line and electrical panel.
Recommend and quote.
You get one or two options with a clear price and an explanation of the differences.
Schedule and install.
We set a date, remove any old unit and install the new one.
Test and hand over.
We check for leaks, combustion and temperature, and show you the shutoffs and the relief valve.
Relocating or upgrading an existing heater.
Moving a heater to open floor space or to cut the distance to the bathrooms is possible. It needs new pipe runs, gas or electric, and a vent path. The cost depends on the distance and the walls involved.
Upgrading from a 30 to a 50 gallon tank is a common request when the family grows. Make sure the closet or alcove can fit the larger unit.
Codes, permits and the Ohio license.
Ohio plumbing contractors are licensed through the Ohio Construction Industry Licensing Board under Chapter 4740 of the Revised Code. Plumbing inspections are the jurisdiction of the county health district under Ohio Administrative Code 1301:3-2-04.
Whether a particular swap needs a permit depends on the local rule and the scope. We tell you at the quote stage so there are no surprises on installation day.
Installs in Ross County homes.
Water in the Chillicothe area comes from the Teays Valley Aquifer, and hardness can build scale in a new heater. We recommend a flush each year and an anode check every few years.
If your house sits low near the Scioto or Paint Creek and has a history of basement water, we mount the heater on a stand and pan it, so a flood does not damage the new unit.
What affects installation pricing.
A clear price comes before any work.
- Unit and efficiency. Larger or higher-efficiency units cost more.
- Venting and fuel work. New flues, gas lines or circuits add scope.
- Code items. Expansion tanks, pans and valves.
- Disposal of the old unit. Removal and haul-away can be included.
Ask your utility and the manufacturer about rebates on efficient models. Keep receipts and the data plate photo for warranty and tax purposes.
Code points on a new heater.
A new heater follows the manufacturer's manual and the Ohio Plumbing Code, built on the International Plumbing Code (IPC), for the relief valve, discharge pipe and expansion control. Gas units add the NFPA 54 National Fuel Gas Code for venting and combustion air. Federal efficiency rules from the U.S. Department of Energy set the minimum efficiency of what you can buy.
What to do before we arrive for an install.
A little preparation makes the job faster and safer.
- Clear a path to the old heater and about three feet of working space around it.
- Shut off the gas at the appliance valve or the breaker for an electric unit.
- Close the cold water supply valve and leave the nearest hot tap open.
- Move stored items and anything flammable away from the heater area.
- Tell us if you smell gas, and leave the house and call 911 or your gas supplier first.
Water heater installation questions.
.
A few days is usual. For tankless or relocations, allow longer for site checks and parts.
.
A like-for-like tank swap takes a few hours. A tankless or a relocation can take most of a day.
.
If your plumbing is a closed system, for example with a check valve or pressure regulator at the main, yes. The heater has nowhere to send expanding water otherwise.
We check this on every install.
.
Yes, if it suits the space and fuel. We check the model first. Warranty terms vary, so ask the seller.
.
We can remove it as part of the install and tell you the cost up front.

